跳至主要内容

How to judge the chilled water flow of the chiller | Oumalchiller.com

 Generally speaking, everyone will have doubts when purchasing a chiller. I don't know how to judge the chilled water flow of the chiller? From what aspects should the water flow of the chiller be considered? Today I would like to share with you four suggestions:

1. Detection of return water temperature and outlet water temperature of the chiller (the unit needs to be in normal state):

30 minutes after starting up the unit, you can read the temperature of the inlet and outlet water when the unit is running through the parameters of the unit's control system or the inlet and outlet water thermometers of the unit's chilled water system. The difference should be ensured to be about 4-6 degrees. If the water temperature difference is too large, it means that the water flow of the water system through the plate type device is too small, which may cause the unit to fail to operate normally or be damaged.


100 HP Air cooled chiller


2. Water pressure detection of the inlet and outlet pipes of the chiller unit:

Through the detection of the return water pressure and the water outlet pressure value, check the water flow rate of the chiller under the pressure difference between the inlet and outlet water in the random manual of the unit. In order to judge whether the water system is normal; and through this difference to judge which section of the water pipeline resistance value is too large, and make corresponding rectification plans and actions.


3. Detection of the suction temperature of the copper tube of the compressor (only in the cooling operation):

If the suction temperature of the compressor is detected to be lower than 0 degrees after the refrigerating chiller is turned on for 30 minutes, it means that the water flow in the water-side heat exchanger is insufficient, resulting in a drop in the evaporating temperature and evaporating pressure, and causing freon to flow in the direction of the evaporator. The suction pipe of the compressor is still evaporating and absorbing heat, which will cause the suction temperature of the compressor to be lower than 0 degrees; in addition, it is necessary to eliminate the drop of evaporating pressure and evaporating temperature caused by the low water temperature set point; The low water temperature unit can be considered normal as long as the compressor has a suction superheat of 6 to 8 °C. Therefore, under normal water flow, the suction temperature of the compressor will generally be greater than 0 °C, below this value, the problem of the water system needs to be eliminated.


4. Water pump running current detection:

By detecting the running current of the chiller water pump and comparing it with the rated current, it can be judged whether the actual water flow rate is larger or smaller than the rated water flow rate of the water pump. Only by making a comprehensive judgment with the previous parameters can an exact water system detection and analysis be obtained. Judgment report.


评论

此博客中的热门博文

Where are water-cooled chillers used? What is a chiller used for?

  Water-cooled chiller   is a cooling water device that can provide constant temperature, constant current and constant pressure. A chiller is a machine that achieves refrigeration through vapor compression or absorption cycles. These liquids can flow through heat exchangers to cool the air or equipment. The industrial chiller can always output ice water with a lower temperature than the ambient temperature. It can be used wherever cooling is required, either direct cooling or indirect heat exchange. The main components of a water-cooled chiller are compressor, condenser, evaporator, water pump, and water tank. Chillers have a wide range of applications. The chiller can be used to cool the injection mold, improve the quality of plastic products, cool the vacuum coating, control the temperature of the vacuum coating machine, cool the food industry, fast cooling processing, chemical industry, effectively control the temperature of chemicals, cooling buildings, concrete fast Cool...

Ways and solutions of noise produced by chillers - www.oumalchiller.com

  It is inevitable that the chiller will produce sound when it is working. For example, when the fan rotates, the fan blades rub against the air, it will produce sound. Normal sound is allowed. However, even the sophisticated refrigeration equipment will appear after a long period of use. Fault. Then, the editor of   Oumal Chiller   will take you to understand the causes and solutions of the noise produced by the chiller. First, find the reason from the parts that are easy to check and observe: 1. Are the anchor screws loose? The chiller is fixed on the ground. After running for a long time, the anchor bolts will be loose, and the chiller will be unstable, which will cause noise. This situation can be solved by replacing the anchor bolts, and vibration reduction can also be installed if conditions permit. The purpose is to make the chiller firmly fixed on the ground. 2. Whether the connecting pipeline is firm There are large and small pipes on the chiller, connecting the ...

How is the Refrigeration Industry Leading the Green Development with R404A

  As global environmental concerns continue to rise, the refrigeration industry is undergoing a significant transformation. Water-cooled low-temperature units exported overseas are now increasingly adopting the eco-friendly refrigerant R404A, leading the way in the industry's green development. Here's a deeper look into this trend. Why Is R404A Becoming the Preferred Refrigerant for  Water-Cooled Low-Temperature Units ? R404A is a blend of refrigerants that stands out due to its environmentally friendly properties. It is free from Ozone Depleting Potential (ODP) and has a relatively low Global Warming Potential (GWP), making it an ideal substitute for traditional refrigerants. This balance between high-performance cooling and environmental friendliness has made R404A especially popular in regions with strict environmental regulations, such as Europe and North America. Water-cooled low-temperature units exported to these areas are now commonly equipped with R404A to meet local ...